Search results for 'Subaru 2008 - 2010'
-
![K&N Typhoon Short Ram Intake Kit [Mitsubishi Lancer]](http://www.aqmotorsports.com/media/catalog/product/cache/1/small_image/300x/17f82f742ffe127f42dca9de82fb58b1/1/0/103b9bcc-492b-4b03-a3f6-1576cacd7d60_7.jpg)
$222.99Built for performance and show. the Typhoon® Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Each kit is proven on a rear-wheel dynamometer to increase horsepower and torque. Typhoon intakes come in one of three designs; cold air intakes (CA). short ram intakes (SR). or complete cold air (CCA) intakes which can be configured as either a cold air intake or a short ram intake. They come with an oversized High-Flow conical air filter designed to provide increased surface area and dust capacity. This extra surface area provides even more airflow at lower restriction than a standard K&N O/E replacement filter that is limited to the size of the factory air box. The oversize air filter also captures more dirt increasing the service life before a cleaning is required (up to 100.000 miles). Some Typhoon Air Intakes are not legal for use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal.
- Designed for increased performance for your sport compacts. utilizing the finest quality components
- Guaranteed to Provide more horsepower and increased acceleration
- Available in high-quality finishes
- Includes K&N High-Flow. Washable/Reusable Air Filter
- Some applications available in cold-air versions
- Easy to Install
- Million Mile Limited Warranty
- Street legal in most states (some not street legal in CA - Check part number or vehicle listing for specific CARB status)
Typhoon Short Ram Intake Kit
Engine :-
Aspiration :- Naturally Aspirated
Vehicle Engine Options :- 4G94.N/A
Vehicle Interior Options :- L4 Aspiration: N
Vehicle Exterior Options :- Fuel: FI-GAS
Cylinder Type :-
Vehicle Options :- Learn More -
$319.00Carrillo Connecting Rods are manufactured from a proprietary steel; manufactured and forged to custom specifications. After experimenting with virtually every other reasonable material; Carrillo found a chromium/nickel/vanadium/molybdenum-forged alloy to be the best product to meet the stringent requirements of performance motors. Through out the manufacturing process Carrillo rods are inspected and measured to uphold high quality standards. When you go with Carrillo you go with quality. These rods are sold PER PIECE as replacement or for test fitment purposes. Learn More -
$535.00For: Mitsubishi Lancer YR: 1992-1995 Cyl: 4 App: 2.0L Turbo Evo 1-3
The FX350 System uses the Power Plus I Pressure Plate with Clutch Masters New Formula Button disc. This clutch is designed for the street enthusiast or weekend racer who plans to abuse their vehicle on an occasional basis and have a spirited driving style. The FX350 clutch system has a higher holding capacity than a segmented Kevlar lining without compromising the street friendly characteristic Clutch Masters is known for. For year’s enthusiast have had to compromise durability for drivability and vise versa, however with Clutch Masters New Formula button we have closed the gap between these two tradeoffs. Learn More -
$399.00Cosworth's been engineering camshafts nearly 50 years. That coupled with years of innovative multi valve cylinder head design ensures camshaft designs the most efficient in providing maximum usable power across widest power band. Each is ground from a billet finished using same procedures we in extreme level race engines. Cosworth camshafts the perfect compliment to CNC Ported Valve Cylinder heads. cams profiled to increase boost response thereby increasing engine torque power are fully compatible with CNC Ported Valve Cylinder Heads.
Key Features
Ground from billets
Engineered tested profiles
Broad power band
Compatible with Cosworth ported Valve Cylinder Heads Learn More -
$156.00To complement the line of Invidia Exhaust Systems; Invidia offers the final piece of the puzzle with Invidia Test Pipes. Manufactured from SUS304 Stainless Steel; these Invidia Test Pipes will replace your stock catalytic converter and unleash the power in your car. Test Pipe
Engine :-
Aspiration :- T
Vehicle Engine Options :- ALL
Vehicle Interior Options :- L4 Aspiration: T
Vehicle Exterior Options :- Fuel: FI-GAS
Cylinder Type :-
Vehicle Options :- Piping 76mm Learn More -
$0.00AEM’s external Peak & Hold Injector Driver module allows ECUÂ’s that have a saturated injector drive circuit to trigger low impedance injectors with a true 4/1 Peak & Hold injector drive circuit.
AEM’s Peak & Hold Injector Driver contains 10 independent injector drive channels. Each channel supplies full battery voltage to a fuel injector for rapid current rise; in order to produce positive injector opening. When load current reaches 4.1A (amps); the injector driver reduces the load current to 1.1A and operates as a constant current source. This condition holds the injector open; and reduces system power dissipation. If the current fails to reach 4.1A within 5mS; the driver module automatically reduces the load current to 1.1A.
Installation is straightforward. Users simply hook the injector trigger wires from an ECU to the module; and then hook the output wires from the module to your injectors. Any number of channels can be used from one to 10.- For high-output engines that have exceeded the capacity of high-impedance injectors
- Includes 10 independent injector drive channels for any engine up to V10
- Complete wiring system included
- Operating Voltage: 8-18 volts; negative ground
- RPM Capability: Unlimited
- Injector Triggers: 10
- Trigger Waveform: Output is activated when input trigger is grounded
- Trigger Impedance: 220 Ohm input impedance; pulled to 12V (60 mA draw)
- Injector Outputs: 10
- Output Current High: 4.15A Peak; Typical
- Output Current Low: 1.15A Sustain; Typical
- Peak Current Timeout: 5mS
- Size: 5.5"L x 4.6"W x 1.4"H
- Weight: 2.7 Lbs
- Over Temperature Shutdown: 115C (Nominal)
Please note:All Prices are subject to change due to exchange rates & price alterations from suppliers.
For more information please click here Learn More -
$81.00Engine bearings one of most vital components within an engine are often overlooked when considering high performance upgrades. Performance engineered; multi-layer bearings generate less heat than normal bearings by reducing friction. Cosworth Race bearing sets feature a unique combination of design; metallurgy engineering to deliver performance in extreme condits. Cosworth Race bearings setsare available in sizes to accommodate most applications. Size 1 bearings a nominal standard size are used most applications. Size 2 bearings feature an additional .001 clearance should be used
when extra clearance is required.
Key Features
High strength overlay plate with reduced thickness better control less friction
Hardened steel backing on connecting bearings
Increased crush better retention
3/4 grooving on Main Bearings providing optimum supply
Tight consistent wall tolerances
Oversize chamfers where applicable
Flash plating eliminated improved heat transfer
Tested to over 1000 horsepower! Learn More -
$164.00Cosworth High Performance Head Gaskets engineered to seal in power under most demanding condits. Constructed from stainless steel with a folded stopper layer; each application features superior sealing compared to conventional multi layer steel gaskets. Additionally; Cosworth High Performance Head Gaskets manufactured from pre-coated cut stainless steel resulting in uniform coating distribution consistent shape.
Key Features
Individual cut layers of stainless steel with superior consistency compared to laser gaskets
Pre-coated stainless steel with a 0.25 micron layer of nitrile rubber ensures consistent distribution of coating with no high or areas
Manufacturing dimensional tolerance of 0.001
Die manufacturing process ensures smooth edges; unlike laser gaskets
Cosworth's gaskets feature a folded stopper layer additional torque around each cylinder. width of sealing area is specific each application thereby providing ultimate sealing properties
Available in a range of thicknesses specific applications Learn More -
$171.00Cosworth High Performance Head Gaskets engineered to seal in power under most demanding condits. Constructed from stainless steel with a folded stopper layer; each application features superior sealing compared to conventional multi layer steel gaskets. Additionally; Cosworth High Performance Head Gaskets manufactured from pre-coated cut stainless steel resulting in uniform coating distribution consistent shape.
Key Features
Individual cut layers of stainless steel with superior consistency compared to laser gaskets
Pre-coated stainless steel with a 0.25 micron layer of nitrile rubber ensures consistent distribution of coating with no high or areas
Manufacturing dimensional tolerance of 0.001
Die manufacturing process ensures smooth edges; unlike laser gaskets
Cosworth's gaskets feature a folded stopper layer additional torque around each cylinder. width of sealing area is specific each application thereby providing ultimate sealing properties
Available in a range of thicknesses specific applications Learn More -
$548.00COMPETITION CLUTCH
Stage 4 Sprung - Strip Series 1620 Clutch KitThis assembly; available with a double spring; six rivet carriage is good for ease of gear transition with higher horsepower. This disc complimented by a performance pressure plate provides up to 250% increase in torque capacity. 300 mile break-in recommended with this set-up.
The 1620 Series kit includes a performance pressure plate; a six puck high torque sprung disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.
Learn More