Search results for 'cosworth stroker kit 2.6l'

The Cosworth ECPro is a higher performance solution engine management. Engineered in conjunction with Pectel Control Systems; Cosworth ECPro features an compatible harness connector a full base calibration allowing to go straight to dyno without workload of full and vehicle configuration.
The Cosworth ECPro is perfect demanding applications such as track day; rally motorsport and is housed in a machined from solid aluminum case with professional motorsport specification electronics. />Features
Designed full harness system integration Plug Perform. Base calibration supplied to a stock engine. There is no need replacement of wiring harness or sensors. Makes of dash diff controller
56Mhz processor. Higher performance timing accuracy control Ethernet comms Fast data offload high quality data viewing on PC
Internal logging memory. configured logging channel configuration at optimum rates performance analysis by your dealer. User define specific logging configurations. on board internal memory up to 2;000Hz of logging bandwidth is standard.
Knock monitoring Control. Advanced knock processing chip offers industry leading advanced knock signal filtration signal processing. MIL lamp indication of Detonation levels (witser defined levels based on and Boost).
Calibration select. (e.g. Fuel save; Test; Race) of OEM SI Drive switch selection of 3 alternate calibrations (calibration selectable boost; fuelling; ignition;rev limit; setting; VCAM target; Fly-By-Wire pedal mapping; overrun fuelling cut-off individually selectable Intelligent; Sports; Sports-Sharp).
Pectel (Anti System) switch (cruise control button) used ALS mode select.
Analog Inputs external sensors. Additional pressure transducers; temperature sensors; digital inputs be wired into EC for logging additional engine parameters and/or additional control strategies. number of analog inputs depends on specific model.
Closed Loop Boost Control. Full closed loop or open loop boost control PID parameters solenoid duty cycle map. Closed loop boost levels also selectable calibration select (see above).
Standard Motorsport Design. Machined billet aluminum case professional motorsports specification electronics.
OEM Narrow Band Supported be disabled by user.
External Wideband Supported. Compatible with wideband units with 0-5v analog output.
Internal Wideband Supported. kit Requires Cosworth by Pectel sensor; requires 3 extra populations 2 relocating. blank pins on harness populating.
Variable CAM. Pre-configured full quad camshaft support />External Comms Support. Optional Motorsport dash center differential controller.
Designed Racing OBDII Motorsport us Learn More

Cosworth stroker kits the perfect to displacement; torque power to your engine. Each includes select matched components from parts list ensuring reliable performance.
Mitsubishi 4B11 (Evolution X) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft (94mm)
Cosworth Forged Connecting Rods
Cosworth'ston Rings
Mitsubishi 4G63 (Evolution VII-IX) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft
(94mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings
Subaru EJ25 2.6L
Cosworth Forged Pistons (99.5mm)
Cosworth Fully Counterweighted Billet Crankshaft
(81mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings Learn More

The Cosworth Subaru High Volume Inlet Manifold is cast from aluminum featuring large tapered runners with radiused inlets improved flow. Plenum volume been substantially increased tuned power. Engineered easy installation is key to making power. Cosworth EJ257 plenum is designed use with 2004-2009 engines equipped with electronic throttle control. plenum is designed use with cable-actuated throttle body EJ20/25 applications. This plenum is designed to replace factory Subaru plenum in vehicles equipped with an aftermarket front-mounted intercooler (FMIC) kit. Throttle body position remains stock; ensuring fitment with brand FMIC kitsigned the stock throttle body intake manifold. 2008-2009 Subaru STIs Cosworth FMIC (p/n 20005378) is highly recommended.
Features
Substantially increased plenum volume
Large; tapered runners with radius inlets
Tuned plenum volume runner length/taper
Over increase in flow
Integral vacuum manifold connection of brake booster; boost gauge; sensor; boost controller; etc.
Will work with standard or forward mount electronic throttle body configurations
Stock throttle body location compatibility with most aftermarket FMIC kits Learn More

Cosworth stroker kits the perfect to displacement; torque power to your engine. Each includes select matched components from parts list ensuring reliable performance.
Mitsubishi 4B11 (Evolution X) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft (94mm)
Cosworth Forged Connecting Rods
Cosworth'ston Rings
Mitsubishi 4G63 (Evolution VII-IX) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft
(94mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings
Subaru EJ25 2.6L
Cosworth Forged Pistons (99.5mm)
Cosworth Fully Counterweighted Billet Crankshaft
(81mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings Learn More

Cosworth High Performance engine assemblies the perfect basis your high performance application. Each version gone through countless hours of engineering evaluation to determine best combination of parts build specification; ensuring maximum reliable performance. Each Cosworth High Performance enginembly starts with new select components as foundation of performance build. Every block is thoroughly inspected before cylinders honed to perfection. We then balance rotating assembly that includes either a factory forged crankshaft or Cosworth Billet crank along with Cosworth Forged connecting rods; Cosworth Tri-Metal bearings Cosworth Forged Pistons. motorsport grade parts then professionally assembled by expert engine builders in Cosworth enginembly facility. Each High Performance enginembly includes a complete specification sheet listing critical dimensions along with a serialized plaque. maximum performance; combine with a Cosworth ported Valve Cylinder Head camshaft set.
Subaru EJ25 High Performance Short Block 2.5L
The Cosworth EJ25 is an excellent starting point high performance track applications.
New Subaru EJ25 EJ257 Block
New Subaru EJ25 Forged Crankshaft or Cosworth Billet Crank (79mm)
Cosworth Forged H-beam connecting rods
Cosworth Forged Pistons (99.5mm) rings
Cosworth Tri-metal bearings
Balanced to within .5 gram
Complete blue-print assembly
Ring set
Bearing clearance checked
Deck height checked
Connecting side clearance checked
Crankshaft float checked
Mitsubishi 4G63 (Evolution VII-IX) High Performance Short Block 2.0L
The Cosworth 2.0L 4G63 is an excellent starting point high performance track applications.
New Mitsubishi 4G63 Evolution Block
New Mitsubishi forged crankshaft (88mm)
Cosworth Forged H-beam connecting rods
Cosworth Forged Pistons (85mm) rings
Cosworth Tri-metal bearings
Cosworth Heavy Duty main studs
Piston squirt jets
Balanced to within .5 gram
Complete blue-print assembly
Ring set
Bearing clearance checked
Deck height checked
Connecting side clearance checked
Crankshaft float checked
Mitsubishi 4G63 (Evolution VII-IX) High Performance Short Block 2.2L
The Cosworth 4G63 2.2L stroker engine combines perfect bore to stroke ratio; yielding potentially gains in torque while still allowing engine to rotate produce power at higher rpms.
New Mitsubishi 4G63 Evolution Block
New Cosworth Billet Crank (94mm)
Cosworth Forged H-beam connecting rods
Cosworth Forged Pistons (86mm) rings
Cosworth Tri-metal bearings
Cosworth Heavy Duty main studs
Piston squirt jets
Balanced to within .5 gram
Complete blue-print assembly
Ring g Learn More

Cosworth stroker kits the perfect to displacement; torque power to your engine. Each includes select matched components from parts list ensuring reliable performance.
Mitsubishi 4B11 (Evolution X) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft (94mm)
Cosworth Forged Connecting Rods
Cosworth'ston Rings
Mitsubishi 4G63 (Evolution VII-IX) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft
(94mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings
Subaru EJ25 2.6L
Cosworth Forged Pistons (99.5mm)
Cosworth Fully Counterweighted Billet Crankshaft
(81mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings Learn More

Cosworth stroker kits the perfect to displacement; torque power to your engine. Each includes select matched components from parts list ensuring reliable performance.
Mitsubishi 4B11 (Evolution X) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft (94mm)
Cosworth Forged Connecting Rods
Cosworth'ston Rings
Mitsubishi 4G63 (Evolution VII-IX) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft
(94mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings
Subaru EJ25 2.6L
Cosworth Forged Pistons (99.5mm)
Cosworth Fully Counterweighted Billet Crankshaft
(81mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings Learn More

Cosworth stroker kits the perfect to displacement; torque power to your engine. Each includes select matched components from parts list ensuring reliable performance.
Mitsubishi 4B11 (Evolution X) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft (94mm)
Cosworth Forged Connecting Rods
Cosworth'ston Rings
Mitsubishi 4G63 (Evolution VII-IX) 2.2L
Cosworth Forged Pistons (86mm)
Cosworth Fully Counterweighted Billet Crankshaft
(94mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings
Subaru EJ25 2.6L
Cosworth Forged Pistons (99.5mm)
Cosworth Fully Counterweighted Billet Crankshaft
(81mm)
Forged Cosworth Connecting Rods
Cosworth and Main Bearings
Cosworth'ston Rings Learn More

To form the ultimate Stroker Kit use with Brian Crower Crankshafts with the corresponding connecting rod and piston combination. The Brian Crower stroker kit delivers a system matched setup that installs correctly the first time.
Although specific differ from kit to kit; you can be sure each Brian Crower Stroker Kit incorporates a larger stroke; steel billet crankshaft not a reworked OEM crank; custom forged aluminum pistons; premium alloy wrist pins; full ring pack; 4340 steel billet connecting rods w/ARP fasteners; and ACL Bearings. All this equals a fully balanced system; ready to install; for some big time power and torque gains. Learn More