Search results for 'the'

COMPETITION CLUTCH
Stage 2 - Street Series 2100 Clutch Kit

This assembly provides up to 80% increase in torque capacity and is properly suited for aggressive street use and moderate track use. The Brass Plus material with its alloy backing matched to a performance pressure plate will provide smooth engagement and extended life. 500 mile break-in highly recommended with this set-up. 300 mile break-in REQUIRED with this set-up. (Some kits may not be supplied with all pieces. Please verify with Competition Clutch before ordering).

The 2100 Series kit includes a performance pressure plate; a high torque sprung disc with antiburst steel backed Brass Plus facings; all applicable bearings; and the appropriate alignment tool.

Learn More

COMPETITION CLUTCH
Stage 5 Rigid - Strip Series 0420 Clutch Kit

This assembly; available with a rigid plate is good for penetrating engagement with higher horsepower applications. This disc complimented by a performance pressure plate provides up to 300% increase in torque capacity. 300 mile break-in recommended with this set-up.

The 0420 Series kit includes a performance pressure plate; a four puck high torque rigid disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.

Learn More

COMPETITION CLUTCH
Stage 3 - Street/Strip Series 2600 Clutch Kit

This segmented Ceramic material with a performance pressure plate will provide the ultimate in street and strip combinations. This assembly is suited for up to 150% increase in torque capacity. Provides quick but smooth engagement and extended life.

The 2600 Series kit includes a performance pressure plate; a high torque sprung disc with segmented Ceramic facings; all applicable bearings; and the appropriate alignment tool.

Learn More

For: Mitsubishi Lancer YR: 2008-2010 Cyl: 4 App: 2.0L Turbo Evo X 5spd
Clutch Masters 725/850 Series: Ultra High Performance Twin Disc Street or Race Systems; 300-600% increase in holding capacity Clutch Masters Twin Disc systems are pure racing technology that also works well in high performance street applications. They are designed to hold tremendous horsepower and torque ratings, while retaining a very smooth operation. By slightly increasing the clamping force of the pressure plate and adding to the square inches of usable disc area, CM Twin Discs significantly increase clamping values with only a 25-50% increase in pedal pressure depending on the application. The cover assembly is machined from billet aluminum with 25% more tensile strength than the competition’s cast unit. The flywheel is machined from billet 6061-T6 aluminum to meet SFI spec 1.2 for competition in NHRA, NDRA, IDRC, IHRA, SCCA and NASA. Each aluminum flywheel includes a replaceable heat shield. Steel flywheels are also available on select applications. *725 SERIES – (7.25” Twin Disc) The 725 series is a smaller diameter assembly, which creates less rotating mass and offering quicker, and smoother shifting with much better throttle response. *850 SERIES – (8.50” Twin Disc) The 850 series is a larger diameter assembly, which is designed for high horsepower applications that require smooth engagement, quiet operation and high clamp load. All systems include: * Cover Assembly with attached Diaphragm * Pressure Plate Ring * Two Discs * One Mid Plate * Billet Aluminum Flywheel* * Release Bearing * Pilot Bearing (when applicable) * Pressure Plate Bolts Learn More

For: Mitsubishi Lancer YR: 2004-2007 Cyl: 4 App: 2.0L O-Z Rally
The FX300 System uses the Power Plus I Pressure Plate with a Steel Back Segmented Kevlar disc. This clutch is designed for the ultimate street enthusiast or weekend racer running a normally aspirated car equipped with cylinder head work and/or hotter cam(s), or with medium-boost turbo or super-charger, or up to 100hp NO2. The FX300 features only slightly increased pedal pressure, long life disc and positive engagement. The FX300 is only recommended for the street and not for the track. Minimum 500 Required break-in miles. Learn More

Flat Rate Shipping: $155 - Please select at checkout.
SEIBON Carbon Fiber Hoods are designed to replace your factory hood and accept all hinges. latches and windshield sprayers for 100% Bolt On fitment. Cut weight in style with SEIBON Carbon Fiber Hoods.
All SEIBON Carbon Fiber Hood should be installed with Hood Pins. Although SEIBON Hoods do bolt-on. it is recommended that vehicles that will be used on street or racing circuits use Hood Pins for additional safety.
All SEIBON Carbon Fiber Products are:

Hand Laid
Wet Carbon Fiber
Clear Gel Coated from the Factory
Inspected Before Shipping Carbon Fiber Hood
EVO Style
Engine :-
Aspiration :- Naturally Aspirated
Vehicle Engine Options :- N/A
Vehicle Interior Options :- L4 Aspiration: N
Vehicle Exterior Options :- Fuel: FI-GAS
Cylinder Type :-
Vehicle Options :-
Carbon Fiber Hood
EVO Style
Engine :-
Aspiration :- Naturally Aspirated
Vehicle Engine Options :- N/A
Vehicle Interior Options :- L4 Aspiration: N
Vehicle Exterior Options :- Fuel: FI-GAS
Cylinder Type :-
Vehicle Options :- Learn More