Search results for 'the'

Cosworth High Valve Springs the result of countless hours of engineering; testing validation ensuring best possible spring high performance applications. Cosworth High Valve Springs wound from worlds finest Japanese Kobe steel feature dual chamfered ends to reduce wear on seats retainers. Each spring been engineered with increased seat pressure along with higher lift capability optimum performance potential improved valve control. Single spring design allows easy installation with no machining required is perfect typical high performance use. />Key Features
Manufactured from finest Japanese Kobe Steel
Single spring design easy installation
Dual chamfered ends
Increased performance Learn More

COMPETITION CLUTCH
Stage 5 Rigid - Strip Series 0420 Clutch Kit

This assembly; available with a rigid plate is good for penetrating engagement with higher horsepower applications. This disc complimented by a performance pressure plate provides up to 300% increase in torque capacity. 300 mile break-in recommended with this set-up.

The 0420 Series kit includes a performance pressure plate; a four puck high torque rigid disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.

Learn More

COMPETITION CLUTCH
Stage 3 - Street/Strip Series 2600 Clutch Kit

This segmented Ceramic material with a performance pressure plate will provide the ultimate in street and strip combinations. This assembly is suited for up to 150% increase in torque capacity. Provides quick but smooth engagement and extended life.

The 2600 Series kit includes a performance pressure plate; a high torque sprung disc with segmented Ceramic facings; all applicable bearings; and the appropriate alignment tool.

Learn More

For: Mitsubishi Lancer YR: 2008-2010 Cyl: 4 App: 2.0L Turbo Evo X 5spd
Clutch Masters 725/850 Series: Ultra High Performance Twin Disc Street or Race Systems; 300-600% increase in holding capacity Clutch Masters Twin Disc systems are pure racing technology that also works well in high performance street applications. They are designed to hold tremendous horsepower and torque ratings, while retaining a very smooth operation. By slightly increasing the clamping force of the pressure plate and adding to the square inches of usable disc area, CM Twin Discs significantly increase clamping values with only a 25-50% increase in pedal pressure depending on the application. The cover assembly is machined from billet aluminum with 25% more tensile strength than the competition’s cast unit. The flywheel is machined from billet 6061-T6 aluminum to meet SFI spec 1.2 for competition in NHRA, NDRA, IDRC, IHRA, SCCA and NASA. Each aluminum flywheel includes a replaceable heat shield. Steel flywheels are also available on select applications. *725 SERIES – (7.25” Twin Disc) The 725 series is a smaller diameter assembly, which creates less rotating mass and offering quicker, and smoother shifting with much better throttle response. *850 SERIES – (8.50” Twin Disc) The 850 series is a larger diameter assembly, which is designed for high horsepower applications that require smooth engagement, quiet operation and high clamp load. All systems include: * Cover Assembly with attached Diaphragm * Pressure Plate Ring * Two Discs * One Mid Plate * Billet Aluminum Flywheel* * Release Bearing * Pilot Bearing (when applicable) * Pressure Plate Bolts Learn More

For: Mitsubishi Lancer YR: 1992-1995 Cyl: 4 App: 2.0L Turbo Evo 1-3
The FX300 System uses the Power Plus I Pressure Plate with a Steel Back Segmented Kevlar disc. This clutch is designed for the ultimate street enthusiast or weekend racer running a normally aspirated car equipped with cylinder head work and/or hotter cam(s), or with medium-boost turbo or super-charger, or up to 100hp NO2. The FX300 features only slightly increased pedal pressure, long life disc and positive engagement. The FX300 is only recommended for the street and not for the track. Minimum 500 Required break-in miles. Learn More

Flat Rate Shipping: $155 - Please select at checkout.
SEIBON Carbon Fiber Front Lips are designed to replace your factory lip (if equipped) or be added to your stock front end for a subtle and stylish look. In addition. many front lips add additional air ducting and down force to the front of your vehicle for added performance.
All SEIBON Carbon Fiber Products are:

Hand Laid
Wet Carbon Fiber
Clear Gel Coated from the Factory
Inspected Before Shipping Carbon Fiber Front Lip
PV Style
Engine :-
Aspiration :- ALL
Vehicle Engine Options :- ALL
Vehicle Interior Options :- ALL Aspiration: ALL
Vehicle Exterior Options :- Fuel: ALL-ALL
Cylinder Type :-
Vehicle Options :-
Carbon Fiber Front Lip
PV Style
Engine :-
Aspiration :- ALL
Vehicle Engine Options :- ALL
Vehicle Interior Options :- ALL Aspiration: ALL
Vehicle Exterior Options :- Fuel: ALL-ALL
Cylinder Type :-
Vehicle Options :- Learn More