Search results for 'Evo x intake'

COMPETITION CLUTCH
Stage 5 Rigid - Strip Series 0420 Clutch Kit

This assembly; available with a rigid plate is good for penetrating engagement with higher horsepower applications. This disc complimented by a performance pressure plate provides up to 300% increase in torque capacity. 300 mile break-in recommended with this set-up.

The 0420 Series kit includes a performance pressure plate; a four puck high torque rigid disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.

Learn More

The Cosworth ECPro is a higher performance solution engine management. Engineered in conjunction with Pectel Control Systems; Cosworth ECPro features an compatible harness connector a full base calibration allowing to go straight to dyno without workload of full and vehicle configuration.
The Cosworth ECPro is perfect demanding applications such as track day; rally motorsport and is housed in a machined from solid aluminum case with professional motorsport specification electronics. />Features
Designed full harness system integration Plug Perform. Base calibration supplied to a stock engine. There is no need replacement of wiring harness or sensors. Makes of dash diff controller
56Mhz processor. Higher performance timing accuracy control Ethernet comms Fast data offload high quality data viewing on PC
Internal logging memory. configured logging channel configuration at optimum rates performance analysis by your dealer. User define specific logging configurations. on board internal memory up to 2;000Hz of logging bandwidth is standard.
Knock monitoring Control. Advanced knock processing chip offers industry leading advanced knock signal filtration signal processing. MIL lamp indication of Detonation levels (witser defined levels based on and Boost).
Calibration select. (e.g. Fuel save; Test; Race) of OEM SI Drive switch selection of 3 alternate calibrations (calibration selectable boost; fuelling; ignition;rev limit; setting; VCAM target; Fly-By-Wire pedal mapping; overrun fuelling cut-off individually selectable Intelligent; Sports; Sports-Sharp).
Pectel (Anti System) switch (cruise control button) used ALS mode select.
Analog Inputs external sensors. Additional pressure transducers; temperature sensors; digital inputs be wired into EC for logging additional engine parameters and/or additional control strategies. number of analog inputs depends on specific model.
Closed Loop Boost Control. Full closed loop or open loop boost control PID parameters solenoid duty cycle map. Closed loop boost levels also selectable calibration select (see above).
Standard Motorsport Design. Machined billet aluminum case professional motorsports specification electronics.
OEM Narrow Band Supported be disabled by user.
External Wideband Supported. Compatible with wideband units with 0-5v analog output.
Internal Wideband Supported. kit Requires Cosworth by Pectel sensor; requires 3 extra populations 2 relocating. blank pins on harness populating.
Variable CAM. Pre-configured full quad camshaft support />External Comms Support. Optional Motorsport dash center differential controller.
Designed Racing OBDII Motorsport us Learn More

Brian Crower high performance camshafts are ground on state-of-the-art CNC cam grinders to insure accuracy and tolerances to within .02mm. Every Brian Crower camshaft profile has been prototyped and dyno tested for proven horsepower results prior to placed into mass production. By grinding cores in high volume; Brian Crower; Inc. is able to pass the cost savings on to the end user. Quality at an affordable price.
Brian Crower uses small diameter grinding wheels during the finishing phase when applicable to generate a more aggressive ramp rate for a faster cylinder fill rate. More air + more fuel = more power. Although it takes longer to grind the cams; research and development has proven that the inverted radius created by the small grinding wheel on the opening side delivers more horsepower on radius and roller rocker applications than the conventional; large diameter grinding wheels.
All Brian Crower cams are checked on a high speed; sub-micron accuracy measuring gauge. The Adcole Camshaft Measuring System uses individual measuring heads for each cam journal and cam lobe; with .01 micron resolution; taking one datum point each 1/10th of a degree or 3;600 data points per revolution. Measuring camshafts for rise error and chattermark detection; this model can measure 200 parts per hour. Learn More