Search results for 'Evo x intake'

For: Mitsubishi Lancer YR: 1996-2000 Cyl: 4 App: 2.0L Turbo Evo 4-6
The FX400 System uses the Power Plus I Pressure Plate with a custom, extremely durable, Sprung Ceramic disc. This is the ultimate extreme duty street and/or road/drag racing system. It is available in a 4,6 or 8 wing (paddle) configuration, with the 4-wing being the more aggressive setup and 8-wing being the less aggressive (please specify which type you prefer). The sprung hub design allows for moderate dampening in high-torque applications, rendering it much more street friendly than solid or rigid designs. This disc is designed for outstanding holding capacity, and rapid heat dissipation. The FX400 ceramic paddle design creates a quick and rapid engagement as well as clutch chatter that may not be ideal for street driven vehicles.  Learn More

COMPETITION CLUTCH
Stage 4 Sprung - Strip Series 1620 Clutch Kit

This assembly; available with a double spring; six rivet carriage is good for ease of gear transition with higher horsepower. This disc complimented by a performance pressure plate provides up to 250% increase in torque capacity. 300 mile break-in recommended with this set-up.

The 1620 Series kit includes a performance pressure plate; a six puck high torque sprung disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.

Learn More

For: Mitsubishi Lancer YR: 1992-1995 Cyl: 4 App: 2.0L Turbo Evo 1-3
Clutch Masters 725/850 Series: Ultra High Performance Twin Disc Street or Race Systems; 300-600% increase in holding capacity Clutch Masters Twin Disc systems are pure racing technology that also works well in high performance street applications. They are designed to hold tremendous horsepower and torque ratings, while retaining a very smooth operation. By slightly increasing the clamping force of the pressure plate and adding to the square inches of usable disc area, CM Twin Discs significantly increase clamping values with only a 25-50% increase in pedal pressure depending on the application. The cover assembly is machined from billet aluminum with 25% more tensile strength than the competition’s cast unit. The flywheel is machined from billet 6061-T6 aluminum to meet SFI spec 1.2 for competition in NHRA, NDRA, IDRC, IHRA, SCCA and NASA. Each aluminum flywheel includes a replaceable heat shield. Steel flywheels are also available on select applications. *725 SERIES – (7.25” Twin Disc) The 725 series is a smaller diameter assembly, which creates less rotating mass and offering quicker, and smoother shifting with much better throttle response. *850 SERIES – (8.50” Twin Disc) The 850 series is a larger diameter assembly, which is designed for high horsepower applications that require smooth engagement, quiet operation and high clamp load. All systems include: * Cover Assembly with attached Diaphragm * Pressure Plate Ring * Two Discs * One Mid Plate * Billet Aluminum Flywheel* * Release Bearing * Pilot Bearing (when applicable) * Pressure Plate Bolts Learn More

COMPETITION CLUTCH
Stage 4 Sprung - Strip Series 1620 Clutch Kit

This assembly; available with a double spring; six rivet carriage is good for ease of gear transition with higher horsepower. This disc complimented by a performance pressure plate provides up to 250% increase in torque capacity. 300 mile break-in recommended with this set-up.

The 1620 Series kit includes a performance pressure plate; a six puck high torque sprung disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.

Learn More

COMPETITION CLUTCH
Stage 5 Rigid - Strip Series 0420 Clutch Kit

This assembly; available with a rigid plate is good for penetrating engagement with higher horsepower applications. This disc complimented by a performance pressure plate provides up to 300% increase in torque capacity. 300 mile break-in recommended with this set-up.

The 0420 Series kit includes a performance pressure plate; a four puck high torque rigid disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.

Learn More

Built for performance and show. the Typhoon® Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles.  Each kit is proven on a rear-wheel dynamometer to increase horsepower and torque. Typhoon intakes come in one of three designs; cold air intakes (CA). short ram intakes (SR). or complete cold air (CCA) intakes which can be configured as either a cold air intake or a short ram intake.  They come with an oversized High-Flow conical air filter designed to provide increased surface area and dust capacity. This extra surface area provides even more airflow at lower restriction than a standard K&N O/E replacement filter that is limited to the size of the factory air box. The oversize air filter also captures more dirt increasing the service life before a cleaning is required (up to 100.000 miles).  Some Typhoon Air Intakes are not legal for use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal.

Designed for increased performance for your sport compacts. utilizing the finest quality components Guaranteed to Provide more horsepower and increased acceleration Available in high-quality finishes Includes K&N High-Flow. Washable/Reusable Air Filter Some applications available in cold-air versions Easy to Install Million Mile Limited Warranty Street legal in most states (some not street legal in CA - Check part number or vehicle listing for specific CARB status)

 

Typhoon Cold Air Intake Kit
Engine :-
Aspiration :- T
Vehicle Engine Options :- ALL
Vehicle Interior Options :- L4 Aspiration: T
Vehicle Exterior Options :- Fuel: FI-GAS
Cylinder Type :-
Vehicle Options :- Learn More

COMPETITION CLUTCH
Stage 4 Sprung - Strip Series 1620 Clutch Kit

This assembly; available with a double spring; six rivet carriage is good for ease of gear transition with higher horsepower. This disc complimented by a performance pressure plate provides up to 250% increase in torque capacity. 300 mile break-in recommended with this set-up.

The 1620 Series kit includes a performance pressure plate; a six puck high torque sprung disc with Ceramic buttons; all applicable bearings; and the appropriate alignment tool.

Learn More

Brian Crower Spring and Retainers
Valvesprings
Designed for high rpm; Brian Crower valve springs are wound from only the highest grade; super clean; chrome silicone alloy and feature proprietary processing procedures (chamfer; debur; etc) for consistent pressures over long term; high rpm usage. Quality valve springs are critical in the prevention of premature valve float.
Retainers
The ultimate in lightweight high performance; Brian Crower titanium retainers typically weigh in approximately 40% less than the factory OEM steel units. CNC machined for premium 6AL4V titanium bar stock to exacting tolerances.
Spring/Retainer Kits
Brian Crower valve spring and titanium retainers kits are system matched to work in unison to deliver better valve control at extended rpms and allow for greater lift camshafts for added performance and reliability.
Keepers/Locks
Spring Seats Learn More

AEM's Plug & Play Engine Management System (EMS) plugs directly into a vehicle's factory ECU harness and requires no additional wiring or hardware. Windows compatible software (2000; XP; NT; 98; 95; ME) makes the task of copying; viewing and manipulating data as simple as a click of the mouse. An integrated tuning wizard allows users to create a base map specifically for a car’s configuration; regardless of what type of injectors; sensors; coils or other changes have been made. The AEM EMS's infinitely adjustable software allows tuners to program virtually any combination of engine control; power adders and auxiliary devices; and accurately delivers proper amounts of fuel and correct ignition timing for any boost level or operating condition.  

• Installs in minutes using Plug & Play technology—no wiring necessary!
• Start-up calibrations included
• Live help window eases tuning process
• Set-up Wizard creates a custom base map for your car
• System is fully enabled—Never pay for upgrades!
• Free software updates on aempower.com
• Uses all the factory sensors
• Runs on Windows™ compatible software
• Fuel table automapping
• Programmable traction control
• Onboard 512kb datalogger
• Up to 10 cylinder sequential fuel injection
• 16 general-purpose outputs
• 7 definable switch inputs
• Electronic boost control
• Soft cut rev limiters
• Two step launch control
• Wet or dry nitrous control
• Definable knock control
• Full idle control
• 4 EGT inputs with fuel control
• 16/32 hybrid high speed processor
  
  Fits EVO 8 see other model for EVO 9

 
Vehicle warranty and legality of use: Installing this performance part(s) on your vehicle may void the vehicles warranty may not meet your states legal requirements for use on public roads (emissions; noise etc – Please check your state law if uncertain). For more information on the sale of performance parts from this site; please read our Terms and Conditions.  
Please note:All Prices are subject to change due to exchange rates & price alterations from suppliers.
For more information please click here Learn More